Internet Connection Sharing on Windows XP

This trick shows you how to share your internet connections on multiple computers within a workgroup with Windows XP. Windows XP has a built-in feature that called "Internet Connection Sharing" (ICS) that allows home users to share their internet connections on multiple computers.
If you are not familiar with the network configurations, the easiest way to share your internet connection is to purchase a router or hub. Use this trick only if you don't have a router, or don't want to use a router, or if you just want to try out the feature.
A simple way to understand this feature is, you are making your host computer (the computer directly connects to the internet) functioning as a router for other computers.

What do you need?

• A "Host" computer that running Windows XP. This computer must have at least TWO (2) network adapters. One adapter - let's call it "Adapter #1" - connects to the internet and another, "Adapter #2", connects to a hub or directly to other computers.
• Client computer(s), which run any version of Windows. A client computer can be connected to the host computer directly by a cross-over cable or indirectly through a hub.
• This trick assumes that the host computer is connected to the internet and you are able to access the internet on this computer.

Configure the Host Computer

1. Logon the host computer as Administrator.
2. Click Start >> Control Panel.
3. Click Network and Internet Connections.
4. Click Network Connections.
5. Right-click the connection that you use to connect to the internet (the connection with Adapter #1). This connection can be either a high-speed internet connection or a dial-up connection.
6. Click Properties.
7. Click Advanced tab.
8. Under Internet Connection Sharing, select the Allow other network users to connect through this computer's Internet connection check box.
9. If you are sharing a dial-up Internet connection, select the Establish a dial-up connection whenever a computer on my network attempts to access the Internet check box if you want to permit your computer to automatically connect to the Internet.
10. Click OK. You'll reieve the following message:
    When Internet Connection Sharing is enabled, your LAN adapter will be set to use IP address 192.168.0.1. Your computer may lose connectivity with other computers on your network. If these other computers have static IP addresses, it is a good idea to set them to obtain their IP addresses automatically. Are you sure you want to enable Internet Connection Sharing?
11. Click Yes.

Configure the Client Computer(s)
To use the shared connection from the Host computer, a client computer must be configured with "Automatic IP address". The main configurations are:

1. Configure TCP/IP Automatic IP
2. Configure Internet Connection

The steps for the above two configurations are vary on different versions of Windows.
The following procedures are for Windows XP client computers.

Log on to the client computer as Administrator or as Owner. Click Start >> Control Panel. Click Network and Internet Connections. Click Network Connections. Right-click Local Area Connection, and then click Properties. Click the General tab, click Internet Protocol (TCP/IP) in the This connection uses the following items list, and then click Properties. In the Internet Protocol (TCP/IP) Properties dialog box, click Obtain an IP address automatically (if it is not already selected), and then click OK. Click Start >> Control Panel Click Network and Internet Connections. Click Internet Options. In the Internet Properties dialog box, click the Connections tab. Click the Setup button. The New Connection Wizard starts. On the Welcome to the New Connection Wizard page, click Next. Click Connect to the Internet, and then click Next. Click Set up my connection manually, and then click Next. Click Connect using a broadband connection that is always on, and then click Next. On the Completing the New Connection Wizard page, click Finish. Exit Control Panel and test the internet. You might need to restart the computer

Browser Shaking

This is a fun little trick that can create a shaking screen on your web browser (i.e. Internet Explorer, etc..)

The trick is simply a small Java Script that causes your browser window to move to different positions, causing a shake of your entire screen. It's kind of cool to watch and see what Java Script can do! Try it out..

Use this trick at your own risk.

Here's how:
Copy this entire line and paste it onto your address box, then press Enter:

javascript:function Shw(n) {if (self.moveBy) {for (i = 35; i > 0; i--) {for (j = n; j > 0; j--) {self.moveBy(1,i);self.moveBy(i,0);self.moveBy(0,-i);self.moveBy(-i,0); } } }} Shw(6)

Convert Any Document or Web Page to PDF

Somebody just told you that you need to have Adobe Acrobat (Writer) to create a PDF file? Guess what, you can get away from that pricey piece of software if you just need to convert some documents to pdf, without a need of fancy editing the pdf document.
Here's how. Thanks to the BullZip, who provides a Free Pdf printer. With this free tool, you can simply "print out" your document or webpage to a pdf file, just about the same way as you print it out to a printer.
You can visit BullZip.com for more information about the software.
Here the direct link to BullZip downloads page: Downloads

1. To get started, first follow the link above and download Free Pdf Printer from BullZip, then install it to your computer.
2. Once you're done, you might need to close the program (or the web browser) which you're currently viewing the document. This helps refreshing the list of available printers on your computer.
3. Once you get back to the document you want to convert, perform the same steps are you print out the document, i.e. File > Print ...
4. When you see the Print window pop-up, select "Bullzip PDF Printer" under "Printers", then click "OK".
5. BullZip PDF Printer will then start to analyze your document and display a new pop-up window, where you can direct it to the location you want to save the pdf file.
6. Follow the pop-up windows and.. hola! The PDF document is created!

Create a boot image from a floppy boot disk

With the CD-ROM available on almost every computer nowaday, more and more computers don't have a floppy drive... What if you have some bootup floppy disks and you just want to keep a copy of them, just in case? Well, you rather not to put the disks in the storage and expecting a few years later, you'd find them and they still work just fine! If you haven't noticed, the quality of floppy disks isn't that good. You don't want to trust your floppy disks.
The solution is simple: make a copy of your floppy disk and save it as a file (an ISO image) on your computer. Then, when you need it, you can either make a new floppy disk or even a CD out of it.
If you need the information to create a bootable CD/DVD with a bootup floppy disk or a bootup ISO image, see this article.
Requirements: Floppy drive, of course!
The following instructions are based on an image utility called MagicISO. You can choose to use a different "image" software, whichever supports this option. MagicISO is not a freeware, but a trial version will still what you need.

The Steps:

1. If you don't already have MagicISO installed, download it here and install it.
2. Launch the MagicISO, if you're using the trial version, click on "Try it"
3. Insert a bootup floppy disk that you want to create an image from.
4. Select "Tools" from the top menu of MagicISO, then select "Make Boot Image from Floppy Disk"
   
   
   
5. At the Save As dialog box, browse to the location you wish to save the image file.
6. Enter the name of the image file under "File name" (i.e. "bootimg.iso") then press "Enter"
   
   
   
7. The image creation progress starts to read the floppy disk and write to the image file.

Microsoft Word Shortcut Keys

The followings are shortcut keys and mouse shortcuts that can be used for Microsoft Word
Use at your own risk.
Mouse shortcuts

Shortcut	Description
Double-click (on a word)	Select the word.
Single-click (anywhere in a sentence) + Holding CTRL	Select the entire sentence.
Triple-click (anywhere in a paragraph)	Select the entire paragraph.
Click, hold, drag, then release	Select text from the click position to release position.
Click first position, hold SHIFT key, then click 2nd position	Select text from the 1st position to the 2nd position.
Hold ALT key, then click and drag	Vertical select text.
Hold CTRL key, then scroll wheel	Zoom in/out.

Keyboard shortcuts

Shortcut	Description
Ctrl + A	Select all (including text, graphics).
Ctrl + B	Bold.
Ctrl + I	Italic.
Ctrl + U	Underline.
Ctrl + C	Copy.
Ctrl + V	Paste.
Ctrl + X	Cut.
Ctrl + F	Find.
Ctrl + Z	Undo.
Ctrl + Y	Redo.
Ctrl + P	Open the print dialog.
Ctrl + K	Insert link.
Ctrl + L	Left align.
Ctrl + E	Center align.
Ctrl + R	Right align.
Ctrl + M	Indent.
Ctrl + (left arrow)	Moves one word to the left.
Ctrl + (right arrow)	Moves one word to the right.
Ctrl + (up arrow)	Moves cursor to the beginning of the paragraph.
Ctrl + (down arrow)	Moves cursor to the end of the paragraph.
Ctrl + Shift + F	Change font.
Ctrl + Shift + *	View/hide non-printing characters.
Ctrl + Del	Deletes word to the right of cursor.
Ctrl + Backspace	Deletes word to the left of cursor.
Ctrl + End	Moves cursor to the end of document.
Ctrl + Home	Moves cursor to the beginning of document.
Ctrl + Spacebar	Reset highlighted text to the default font.
Ctrl + 1	Single-space.
Ctrl + 2	Double-space.
Ctrl + 5	1.5-line.
Ctrl + Alt + 1	Format text: heading 1.
Ctrl + Alt + 2	Format text: heading 2.
Ctrl + Alt + 3	Format text: heading 3.
F1	Help.
F4	Repeat the last action
F5	Go to .
F7	Spelling and grammar.
F12	Save as.
F8 then (left arrow)	Increase selection to the left by one character
F8 then (right arrow)	Increase selection to the right by one character
Ctrl + F1	Task Pane.
Ctrl + F2	Print preview.
Alt + Ctrl + F2	New document.
Shift + F3	Cycle between capitalized formats
Ctrl + Insert	Copy.
Shift + Insert	Paste.
Shift + End	Select from current position to the end of the line.
Shift + Home	Select from current position to the beginning of the line.
Ctrl + Shift + (left arrow)	Select from current position to the beginning of the word.
Ctrl + Shift + (right arrow)	Select from current position to the end of the word.
Ctrl + Shift + (up arrow)	Select from current position to the beginning of the document.
Ctrl + Shift + (down arrow)	Select from current position to the end of the document.
Ctrl + Shift + Page Up	Select from current position to the beginning of the window.
Ctrl + Shift + Page Down	Select from current position to the end of the window.
Shift + Page Up	One screen page up.
Shift + Page Down	One screen page down.
Shift + F7	Thesaurus check selected text.
Shift + F12	Save.
Ctrl + Shift + F12	Print.
Alt + Shift + D	Insert the current date.
Alt + Shift + T	Insert the current time.

Add Author Information into Word Document

This trick shows you how to add some additional information to a Microsoft Word document. The information can be the name of the author, company, title, revision number, etc... When you open the folder which contains your document, and point the mouse to the document, the information will be displayed.

Here's a sample

Here's how

1. Open the folder that contains the document.
   
2. Right-click on the document and select "Properties".
   
3. On the "Properties" dialog, select the "Summary" tab.
   
4. Under the "Summary" tab, the fields are listed by two columns "Property" on the left and "Value" on the right.
   
   
   
   
5. Click on a field (i.e. "title") you want to edit, then edit its value. Then click "OK"  

Add Watermark to a Word Document

You can insert a watermark into a Microsoft Word document as either text or image.
Here is a sample Word Document with text watermark:

And here is an example of picture watermark:



Step-by-step to add a watermark to Word document (applied for Microsoft Word 97-2010):
Microsoft Word 97/2000/XP (2002)/2003:

1. Open the Word document that you want to add watermark to.
2. Select "Format" from the top menu, then select "Background", then "Printed Watermark".
3. In the "Printed Watermark" dialog:
   
   A. To insert a text watermark:
   • Select the "Text watermark".
   • Then, either select a pre-defined text from the drop-down, or type in your desire text on the "Text" field.
   • Customize your watermark with other options in this dialog such as text size, text color, etc, then click "OK".
   • Watermark is now inserted into your document.
   
   B. To insert an image watermark:
   • Select the "Picture watermark".
   • Then click on the button "Select Picture...".
   • Navigate to the directory where your watermark picture is located. Select it and click "Insert".
   • Select a customized scale if desired, then click "OK".
   • The image is now inserted into your document as watermark.

Microsoft Word 2007/2010:

1. Open the Word document that you want to add watermark to.
2. Select the "Page Layout" Tab from the top menu
3. In the "Page Background" group, select "Watermark".
4. You can now select one of the pre-defined watermarks, or if you wish to use your own text/image, select "Custom Watermark" at the bottom.
   At the "Printed Watermark" dialog:
   
   A. To insert a text watermark:
   • Select the "Text watermark".
   • Then, either select a pre-defined text from the drop-down, or type in your desire text on the "Text" field.
   • Customize your watermark with other options in this dialog such as text size, text color, etc, then click "OK".
   • Watermark is now inserted into your document.
   
   B. To insert an image watermark:
   • Select the "Picture watermark".
   • Then click on the button "Select Picture...".
   • Navigate to the directory where your watermark picture is located. Select it and click "Insert".
   • Select a customized scale if desired, then click "OK".
   • The image is now inserted into your document as watermark.